Start refactoring instructions.

[fpgaboy.git] / System.v

`timescale 1ns / 1ps
module ROM(
	input [15:0] address,
	inout [7:0] data,
	input clk,
	input wr, rd);

	reg [7:0] rom [2047:0];
	initial $readmemh("rom.hex", rom);

	wire decode = address[15:13] == 0;
	wire [7:0] odata = rom[address[11:0]];
	assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
	//assign data = rd ? odata : 8'bzzzzzzzz;
endmodule

module InternalRAM(
	input [15:0] address,
	inout [7:0] data,
	input clk,
	input wr, rd);
	
	// synthesis attribute ram_style of reg is block
	reg [7:0] ram [8191:0];
	
	wire decode = address[15:13] == 3'b110;
	reg [7:0] odata;
	wire idata = data;
	assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
	
	always @(negedge clk)
	begin
		if (decode)	// This has to go this way. The only way XST knows how to do
		begin				// block ram is chip select, write enable, and always
			if (wr)		// reading. "else if rd" does not cut it ...
				ram[address[12:0]] <= data;
			odata <= ram[address[12:0]];
		end
	end
endmodule

module Switches(
	input [15:0] address,
	inout [7:0] data,
	input clk,
	input wr, rd,
	input [7:0] switches,
	output reg [7:0] ledout = 0);
	
	wire decode = address == 16'hFF51;
	reg [7:0] odata;
	assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
	
	always @(negedge clk)
	begin
		if (decode && rd)
			odata <= switches;
		else if (decode && wr)
			ledout <= data;
	end
endmodule

module CoreTop(
	input xtal,
	input [7:0] switches,
	input [3:0] buttons,
	output wire [7:0] leds,
	output serio,
	output wire [3:0] digits,
	output wire [7:0] seven);
	
	wire clk;	
	CPUDCM dcm (.CLKIN_IN(xtal), .CLKFX_OUT(clk));

	wire [15:0] addr;	
	wire [7:0] data;
	wire wr, rd;
	
	wire irq, tmrirq;
	wire [7:0] jaddr;

	GBZ80Core core(
		.clk(clk),
		.busaddress(addr),
		.busdata(data),
		.buswr(wr),
		.busrd(rd),
		.irq(irq),
		.jaddr(jaddr));
	
	ROM rom(
		.address(addr),
		.data(data),
		.clk(clk),
		.wr(wr),
		.rd(rd));
	
	AddrMon amon(
    .addr(addr), 
    .clk(clk), 
    .digit(digits), 
    .out(seven),
	 .freeze(buttons[0])
    );
	 
	Switches sw(
		.address(addr),
		.data(data),
		.clk(clk),
		.wr(wr),
		.rd(rd),
		.ledout(leds),
		.switches(switches)
		);

	UART nouart (	/* no u */
    .clk(clk), 
    .wr(wr), 
    .rd(rd), 
    .addr(addr), 
    .data(data), 
    .serial(serio)
    );

  InternalRAM ram(
		.address(addr),
		.data(data),
		.clk(clk),
		.wr(wr),
		.rd(rd));

	Timer tmr(
		.clk(clk),
		.wr(wr),
		.rd(rd),
		.addr(addr),
		.data(data),
		.irq(tmrirq));
	
	Interrupt intr(
		.clk(clk),
		.rd(rd),
		.wr(wr),
		.addr(addr),
		.data(data),
		.vblank(0),
		.lcdc(0),
		.tovf(tmrirq),
		.serial(0),
		.buttons(0),
		.master(irq),
		.jaddr(jaddr));
endmodule

module TestBench();
	reg clk = 1;
	wire [15:0] addr;
	wire [7:0] data;
	wire wr, rd;
	
	wire irq, tmrirq;
	wire [7:0] jaddr;
	
	wire [7:0] leds;
	wire [7:0] switches;
	
	always #10 clk <= ~clk;
	GBZ80Core core(
		.clk(clk),
		.busaddress(addr),
		.busdata(data),
		.buswr(wr),
		.busrd(rd),
		.irq(irq),
		.jaddr(jaddr));
	
	ROM rom(
		.clk(clk),
		.address(addr),
		.data(data),
		.wr(wr),
		.rd(rd));
	
	InternalRAM ram(
		.address(addr),
		.data(data),
		.clk(clk),
		.wr(wr),
		.rd(rd));

	wire serio;
	UART uart(
		.addr(addr),
		.data(data),
		.clk(clk),
		.wr(wr),
		.rd(rd),
		.serial(serio));
	
	Timer tmr(
		.clk(clk),
		.wr(wr),
		.rd(rd),
		.addr(addr),
		.data(data),
		.irq(tmrirq));
	
	Interrupt intr(
		.clk(clk),
		.rd(rd),
		.wr(wr),
		.addr(addr),
		.data(data),
		.vblank(0),
		.lcdc(0),
		.tovf(tmrirq),
		.serial(0),
		.buttons(0),
		.master(irq),
		.jaddr(jaddr));
	
	Switches sw(
		.clk(clk),
		.address(addr),
		.data(data),
		.wr(wr),
		.rd(rd),
		.switches(switches),
		.ledout(leds));
endmodule