Cut 1 at an onboard bootloader

[fpgaboy.git] / Uart.v

`define IN_CLK 8388608
`define OUT_CLK 57600
`define CLK_DIV `IN_CLK / `OUT_CLK
`define DATA_ADDR 16'hFF52
`define STAT_ADDR 16'hFF53

module UART(
	input clk,
	input wr,
	input rd,
	input [15:0] addr,
	inout [7:0] data,
	output reg serial = 1,
	input serialrx);

	wire data_decode = (addr == `DATA_ADDR);
	wire stat_decode = (addr == `STAT_ADDR);
	reg data_latch = 0;
	reg stat_latch = 0;
	
	reg [7:0] tx_data = 0;
	reg [15:0] tx_clkdiv = 0;
	reg [3:0] tx_state = 4'b0000;
	reg tx_busy = 0;
	wire tx_newdata = (wr) && (!tx_busy) && data_decode;
	
	reg rx_hasdata = 0;
	reg [15:0] rx_clkdiv = 0;
	reg [3:0] rx_state = 4'b0000;
	reg [7:0] rx_data;
	
	assign data = (stat_latch) ? {6'b0, rx_hasdata, tx_busy} :
			(data_latch) ? rx_data :
			8'bzzzzzzzz;

	always @(posedge clk)
	begin
		data_latch <= rd && data_decode;
		stat_latch <= rd && stat_decode;
		if(tx_newdata) begin
			tx_data <= data;
			tx_state <= 4'b0000;
			tx_busy <= 1;
		end else if (tx_clkdiv == 0) begin
			tx_state <= tx_state + 1;
			if (tx_busy)
				case (tx_state)
				4'b0000: serial <= 0;
				4'b0001: serial <= tx_data[0];
				4'b0010: serial <= tx_data[1];
				4'b0011: serial <= tx_data[2];
				4'b0100: serial <= tx_data[3];
				4'b0101: serial <= tx_data[4];
				4'b0110: serial <= tx_data[5];
				4'b0111: serial <= tx_data[6];
				4'b1000: serial <= tx_data[7];
				4'b1001: serial <= 1;
				4'b1010: tx_busy <= 0;
				default: $stop;
				endcase
		end
		
		if ((rx_state == 0) && (serialrx == 0) /*&& (rx_hasdata == 0)*/)		/* Kick off. */
			rx_state <= 4'b0001;
		else if ((rx_state != 4'b0000) && (rx_clkdiv == 0)) begin
			if (rx_state != 4'b1010)
				rx_state <= rx_state + 1;
			else
				rx_state <= 0;
			case (rx_state)
			4'b0001:	begin end /* Twiddle thumbs -- this is the end of the half bit. */
			4'b0010:	rx_data[0] <= serialrx;
			4'b0011:	rx_data[1] <= serialrx;
			4'b0100:	rx_data[2] <= serialrx;
			4'b0101:	rx_data[3] <= serialrx;
			4'b0110:	rx_data[4] <= serialrx;
			4'b0111:	rx_data[5] <= serialrx;
			4'b1000:	rx_data[6] <= serialrx;
			4'b1001:	rx_data[7] <= serialrx;
			4'b1010:	begin end /* Expect a 1 */
			endcase
		end
		
		rx_hasdata <= (rx_hasdata && ~(rd && data_decode)) || ((rx_state == 4'b1010) && (tx_clkdiv == 0));

		if(tx_newdata || (tx_clkdiv == `CLK_DIV))
			tx_clkdiv <= 0;
		else
			tx_clkdiv <= tx_clkdiv + 1;
		
		if ((rx_state == 0) && (serialrx == 0) /*&& (rx_hasdata == 0)*/)		/* Wait half a period before advancing. */
			rx_clkdiv <= `CLK_DIV / 2 + `CLK_DIV / 4;
		else if (rx_clkdiv == `CLK_DIV)
			rx_clkdiv <= 0;
		else
			rx_clkdiv <= rx_clkdiv + 1;
	end
endmodule