input clk,
input wr, rd);
- reg [7:0] rom [2047:0];
+ reg [7:0] odata;
+
+ // synthesis attribute ram_style of rom is block
+ reg [7:0] rom [1023:0];
initial $readmemh("rom.hex", rom);
wire decode = address[15:13] == 0;
- wire [7:0] odata = rom[address[11:0]];
+ always @(posedge clk)
+ odata <= rom[address[10:0]];
+ assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
+endmodule
+
+module BootstrapROM(
+ input [15:0] address,
+ inout [7:0] data,
+ input clk,
+ input wr, rd);
+
+ reg [7:0] brom [255:0];
+ initial $readmemh("bootstrap.hex", brom);
+
+ wire decode = address[15:8] == 0;
+ wire [7:0] odata = brom[address[7:0]];
+ assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
+endmodule
+
+module MiniRAM(
+ input [15:0] address,
+ inout [7:0] data,
+ input clk,
+ input wr, rd);
+
+ reg [7:0] ram [127:0];
+
+ wire decode = (address >= 16'hFF80) && (address <= 16'hFFFE);
+ reg [7:0] odata;
assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
- //assign data = rd ? odata : 8'bzzzzzzzz;
+
+ always @(posedge clk)
+ begin
+ if (decode) // This has to go this way. The only way XST knows how to do
+ begin // block ram is chip select, write enable, and always
+ if (wr) // reading. "else if rd" does not cut it ...
+ ram[address[6:0]] <= data;
+ odata <= ram[address[6:0]];
+ end
+ end
endmodule
module InternalRAM(
input clk,
input wr, rd);
- // synthesis attribute ram_style of reg is block
+ // synthesis attribute ram_style of ram is block
reg [7:0] ram [8191:0];
wire decode = address[15:13] == 3'b110;
reg [7:0] odata;
- wire idata = data;
assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
- always @(negedge clk)
+ always @(posedge clk)
begin
if (decode) // This has to go this way. The only way XST knows how to do
begin // block ram is chip select, write enable, and always
reg [7:0] odata;
assign data = (rd && decode) ? odata : 8'bzzzzzzzz;
- always @(negedge clk)
+ always @(posedge clk)
begin
if (decode && rd)
odata <= switches;
end
endmodule
+`ifdef isim
+module Dumpable(input [2:0] r, g, input [1:0] b, input hs, vs, vgaclk);
+endmodule
+`endif
+
module CoreTop(
+`ifdef isim
+ output reg vgaclk = 0,
+ output reg clk = 0,
+`else
input xtal,
input [7:0] switches,
input [3:0] buttons,
output wire [7:0] leds,
output serio,
output wire [3:0] digits,
- output wire [7:0] seven);
+ output wire [7:0] seven,
+`endif
+ output wire hs, vs,
+ output wire [2:0] r, g,
+ output wire [1:0] b,
+ output wire soundl, soundr);
+
+`ifdef isim
+ always #62 clk <= ~clk;
+ always #100 vgaclk <= ~vgaclk;
+
+ Dumpable dump(r,g,b,hs,vs,vgaclk);
- wire clk;
- CPUDCM dcm (.CLKIN_IN(xtal), .CLKFX_OUT(clk));
+ wire [7:0] leds;
+ wire serio;
+ wire [3:0] digits;
+ wire [7:0] seven;
+ wire [7:0] switches = 8'b0;
+ wire [3:0] buttons = 4'b0;
+`else
+ wire xtalb, clk, vgaclk;
+ IBUFG iclkbuf(.O(xtalb), .I(xtal));
+ CPUDCM dcm (.CLKIN_IN(xtalb), .CLKFX_OUT(clk));
+ pixDCM pixdcm (.CLKIN_IN(xtalb), .CLKFX_OUT(vgaclk));
+`endif
- wire [15:0] addr;
- wire [7:0] data;
- wire wr, rd;
+ wire [15:0] addr [1:0];
+ wire [7:0] data [1:0];
+ wire wr [1:0], rd [1:0];
- wire irq, tmrirq;
+ wire irq, tmrirq, lcdcirq, vblankirq;
wire [7:0] jaddr;
-
+ wire [1:0] state;
+
GBZ80Core core(
.clk(clk),
- .busaddress(addr),
- .busdata(data),
- .buswr(wr),
- .busrd(rd),
+ .bus0address(addr[0]),
+ .bus0data(data[0]),
+ .bus0wr(wr[0]),
+ .bus0rd(rd[0]),
+ .bus1address(addr[1]),
+ .bus1data(data[1]),
+ .bus1wr(wr[1]),
+ .bus1rd(rd[1]),
.irq(irq),
- .jaddr(jaddr));
+ .jaddr(jaddr),
+ .state(state));
+
+ BootstrapROM brom(
+ .address(addr[1]),
+ .data(data[1]),
+ .clk(clk),
+ .wr(wr[1]),
+ .rd(rd[1]));
ROM rom(
- .address(addr),
- .data(data),
+ .address(addr[0]),
+ .data(data[0]),
.clk(clk),
- .wr(wr),
- .rd(rd));
+ .wr(wr[0]),
+ .rd(rd[0]));
+
+ wire lcdhs, lcdvs, lcdclk;
+ wire [2:0] lcdr, lcdg;
+ wire [1:0] lcdb;
+
+ LCDC lcdc(
+ .clk(clk),
+ .addr(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0]),
+ .lcdcirq(lcdcirq),
+ .vblankirq(vblankirq),
+ .lcdclk(lcdclk),
+ .lcdhs(lcdhs),
+ .lcdvs(lcdvs),
+ .lcdr(lcdr),
+ .lcdg(lcdg),
+ .lcdb(lcdb));
+
+ Framebuffer fb(
+ .lcdclk(lcdclk),
+ .lcdhs(lcdhs),
+ .lcdvs(lcdvs),
+ .lcdr(lcdr),
+ .lcdg(lcdg),
+ .lcdb(lcdb),
+ .vgaclk(vgaclk),
+ .vgahs(hs),
+ .vgavs(vs),
+ .vgar(r),
+ .vgag(g),
+ .vgab(b));
AddrMon amon(
- .addr(addr),
- .clk(clk),
- .digit(digits),
- .out(seven),
- .freeze(buttons[0])
- );
+ .clk(clk),
+ .addr(addr[0]),
+ .digit(digits),
+ .out(seven),
+ .freeze(buttons[0]),
+ .periods(
+ (state == 2'b00) ? 4'b0010 :
+ (state == 2'b01) ? 4'b0001 :
+ (state == 2'b10) ? 4'b1000 :
+ 4'b0100) );
Switches sw(
- .address(addr),
- .data(data),
.clk(clk),
- .wr(wr),
- .rd(rd),
+ .address(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0]),
.ledout(leds),
.switches(switches)
);
UART nouart ( /* no u */
- .clk(clk),
- .wr(wr),
- .rd(rd),
- .addr(addr),
- .data(data),
- .serial(serio)
- );
-
- InternalRAM ram(
- .address(addr),
- .data(data),
.clk(clk),
- .wr(wr),
- .rd(rd));
-
- Timer tmr(
- .clk(clk),
- .wr(wr),
- .rd(rd),
- .addr(addr),
- .data(data),
- .irq(tmrirq));
-
- Interrupt intr(
- .clk(clk),
- .rd(rd),
- .wr(wr),
- .addr(addr),
- .data(data),
- .vblank(0),
- .lcdc(0),
- .tovf(tmrirq),
- .serial(0),
- .buttons(0),
- .master(irq),
- .jaddr(jaddr));
-endmodule
+ .addr(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0]),
+ .serial(serio)
+ );
-module TestBench();
- reg clk = 1;
- wire [15:0] addr;
- wire [7:0] data;
- wire wr, rd;
-
- wire irq, tmrirq;
- wire [7:0] jaddr;
-
- wire [7:0] leds;
- wire [7:0] switches;
-
- always #10 clk <= ~clk;
- GBZ80Core core(
- .clk(clk),
- .busaddress(addr),
- .busdata(data),
- .buswr(wr),
- .busrd(rd),
- .irq(irq),
- .jaddr(jaddr));
-
- ROM rom(
+ InternalRAM ram(
.clk(clk),
- .address(addr),
- .data(data),
- .wr(wr),
- .rd(rd));
+ .address(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0])
+ );
- InternalRAM ram(
- .address(addr),
- .data(data),
+ MiniRAM mram(
.clk(clk),
- .wr(wr),
- .rd(rd));
+ .address(addr[1]),
+ .data(data[1]),
+ .wr(wr[1]),
+ .rd(rd[1])
+ );
- wire serio;
- UART uart(
- .addr(addr),
- .data(data),
- .clk(clk),
- .wr(wr),
- .rd(rd),
- .serial(serio));
-
Timer tmr(
.clk(clk),
- .wr(wr),
- .rd(rd),
- .addr(addr),
- .data(data),
- .irq(tmrirq));
+ .addr(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0]),
+ .irq(tmrirq)
+ );
Interrupt intr(
.clk(clk),
- .rd(rd),
- .wr(wr),
- .addr(addr),
- .data(data),
- .vblank(0),
- .lcdc(0),
+ .addr(addr[0]),
+ .data(data[0]),
+ .wr(wr[0]),
+ .rd(rd[0]),
+ .vblank(vblankirq),
+ .lcdc(lcdcirq),
.tovf(tmrirq),
- .serial(0),
- .buttons(0),
+ .serial(1'b0),
+ .buttons(1'b0),
.master(irq),
.jaddr(jaddr));
- Switches sw(
- .clk(clk),
- .address(addr),
- .data(data),
- .wr(wr),
- .rd(rd),
- .switches(switches),
- .ledout(leds));
+ Soundcore sound(
+ .core_clk(clk),
+ .addr(addr[0]),
+ .data(data[0]),
+ .rd(rd[0]),
+ .wr(wr[0]),
+ .snd_data_l(soundl),
+ .snd_data_r(soundr));
endmodule